manualshive.com logo in svg

Siemens SITRANS WW100, Руководство по эксплуатации

Поделиться
Скачать
Siemens SITRANS WW100 Скачать руководство пользователя страница 16

Test the functionality of the drive and weighfeeder. Also note the direction of belt travel; if 

incorrect, refer to P1113 (Page 18) to invert the signal for belt direction.

Note
Please refer to Additional notes and important information (Page 19) for details on required 

enable signals.

4.2.1.2

Switching units

Note
While commissioning using the BOP 20 interface standard equipment, there are two data sets 

to consider when changing parameters:
● The drive unit or DDS (Drive Data Set) will be identified as 02. 
● The Control unit CDS (Command Data Set) will be identified as 01.
This data set is indicated in the drive number field 

②

. Each unit has its own set of parameters 

and is only available when in that specific display mode.

The following diagram illustrates how to switch from one unit to another using the BOP Keypad.

1. While holding the   key, press one of the arrow keys (  or 

). This will allow you to 

change from Unit 01 to 02 as indicated by the flashing display.

2. Scroll to the appropriate selection using the arrow keys.
3. Once you have chosen the appropriate unit, press the   key to acknowledge the selection: 

the display will stop flashing. 

4.2.1.3

P0003 - Expert mode

P0003 must be set to EXPERT MODE to access/modify parameter settings.
1. Set S120 display to drive number 01 (see Switching units (Page 16)).
2. Use   or 

 arrows to navigate to P0003.

3. Press 

 so the current parameter value is displayed.

4. Press   to activate edit mode (display will flash).

Installing
4.2 Electrical installation for servo driven models

SITRANS WW100

16

Operating Instructions, 06/2018, A5E33560618-AC

Содержание SITRANS WW100















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды