manualshive.com logo in svg

Siemens SITRANS WW100, Руководство по эксплуатации

Поделиться
Скачать
Siemens SITRANS WW100 Скачать руководство пользователя страница 23

Calibrating

5

After the weighfeeder has been properly installed, calibration of the weighing system must be 

done in conjunction with the integrator. Refer to the integrator instruction manual for 

programming and calibration. 
A test sheet has been provided with the weighfeeder detailing the entries used during factory 

calibration.
The calibration is initially done using the supplied test chain. (For models with skirtboard 

covers, the cover will need to be removed for test chain calibration. The shear gate may also 

need to be raised to apply the calibration chains to the belt.) Material tests are recommended 

to achieve maximum accuracy.

5.1

Test load

The test load value for the weighfeeder is based on the number of chain strands. The exact 

weight of the test strand is stamped on it. 

5.2

Zero

Perform the zero calibration as described in the Calibration section of the integrator manual.

Note
This calibration should be at least three belt revolutions or five minutes, whichever is longer.

5.3

Span

The test load used in the calibration procedure is the test chain provided that mounts to the 

conveyor leg with two mount screws.
Perform the span calibration as described in the Calibration section of the integrator instruction 

manual. 

Note
This calibration should be at least three belt revolutions or five minutes, whichever is longer.

SITRANS WW100

Operating Instructions, 06/2018, A5E33560618-AC

23

Содержание SITRANS WW100















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды