manualshive.com logo in svg

Siemens SITRANS WW100, Руководство по эксплуатации

Поделиться
Скачать
Siemens SITRANS WW100 Скачать руководство пользователя страница 18

4. To change this value, press the   key The display will begin to flash. Sequentially pressing 

the   key will increment

the display to the next higher digit.

5. Use   or 

 arrows to set the RPM value (as calculated above).

6. Press 

 to accept the new value and exit edit mode (display will stop flashing).

Note
Although this value has been changed, it has only been saved in RAM memory. A RAM to 

ROM must be performed in order to be maintained.

7. To save this new setting, press and hold 

 for 3 seconds. The display will begin to flash 

indicating the RAM to ROM function is active. This will perform a RAM to ROM backup of all 

parameters.

P1113 - Belt direction

P1113 – SetPoint Inversion Parameter. Drive 02 parameter
If the belt is travelling in reverse, change P1113 setting to alternate value.
The design of the WW100 weighfeeder is such that the servo Gear motor can be mounted on 

either the left or right hand side of the weighfeeder. Given the versatility of the configuration, it 

is necessary for the motor shaft output to be reversible. Therefore, parameter P1113 can be set 

to accommodate a forward or reverse operation. However, one must note that the BOP display 

for RPM may reflect a negative - 0.00 value. This is not a concern to the operator or 

maintenance staff for regular operation of the drive.
If the weighfeeder is set up and you realize the belt is traveling in the reverse direction, proceed 

as follows:
1. Set S120 display to drive number 02 (see Switching units (Page 16)).
2. Use   or

 arrows to navigate to P1113.

3. Press

 so the current parameter value is displayed.

4. Press  to activate edit mode (display will flash).
5. Use or

 arrows to set the value to either 0 or 1 (whichever is the alternate).

6. Press 

 to accept the new value, and exit edit mode (display will stop flashing).

Note
Although this value has been changed, it has only been saved in RAM memory. A RAM to 

ROM must be performed in order to be maintained.

7. To save this new setting, press and hold 

 for 3 seconds. The display will begin to flash 

indicating the RAM to ROM function is active. This will perform a RAM to ROM backup of all 

parameters.

Installing
4.2 Electrical installation for servo driven models

SITRANS WW100

18

Operating Instructions, 06/2018, A5E33560618-AC

Содержание SITRANS WW100















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды