manualshive.com logo in svg

Siemens SITRANS WW100, Руководство по эксплуатации

Поделиться
Скачать
Siemens SITRANS WW100 Скачать руководство пользователя страница 19

Saving parameter changes

Note
When you make changes to a parameter with the BOP, they are maintained only in the RAM 

memory so that if the power is cycled prior to performing a Save Function, your changes will be 

lost. To avoid this, save the data set either to the ROM-Non Volatile Memory, or both the 

ROM and Micro Memory Card. Both options are described below.

RAM to ROM
At any point during the commissioning, the data can be saved to non-volatile memory. This is 

initiated by pressing and holding the   key for three seconds. The display will begin to flash, 

indicating the RAM to ROM function is active.
When complete, the display will stop flashing and remain solid.

RAM to ROM 

and Micro Memory Card, P977=1.

1. Set S120 display to drive number 01 (see Switching units (Page 16)).
2. With the Power ON, insert the Micro Memory Card into the card slot below the BOP Display 

and ensure the card locks into place.

3. Use   or

 arrows to navigate to P0977.

4. Press

 so the current parameter value is displayed. The default value is 0. Any other value 

initiates a function within the Control Unit.

5. Use or

 arrows to set the value to 1.

The display will begin to flash indicating that the save function is active. The Data Set 

currently active in the RAM will be saved to the ROM (Non-Volatile Memory) as well as the 

MMC card. 

Note
This type of saving will overwrite any existing Data Set with the index of 0 on the Micro 

Memory Card. You should only have a Data Set with an index of 0.

4.2.1.5

Additional notes and important information

Inputs and outputs

All inputs and outputs are identified on the schematics act as discreet I/O to the CU305DP 

Control Module. All related functions for the I/O are programmed internally to the Control Unit, 

therefore, requiring specific States and or Change in States for proper drive functionality.
Please review the electrical schematics to understand what inputs are required for Hand or 

Automatic mode enable signals as well as the Analog Speed reference signals.
Each of the labeled inputs has been programmed into an AND/OR gate function, and therefore 

is required for operation of the drive. A brief description below will help explain the input 

requirements:

Installing

4.2 Electrical installation for servo driven models

SITRANS WW100

Operating Instructions, 06/2018, A5E33560618-AC

19

Содержание SITRANS WW100















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды