Siemens SITRANS LR140 Скачать руководство пользователя страница 40

Страница: 40 / 58

Diagnostics and troubleshooting

9.4 Status messages according to NE 107

Out of specification

Code
Text message

Cause

Rectification

S600
Impermissible

electronics

temperature

Temperature of the electronics in the

non-specified range

Check ambient temperature
Insulate electronics

S601
Overfilling

Danger of vessel overfilling

Make sure that there is no further

filling
Check level in the vessel

S603
Impermissible

operating voltage

Terminal voltage too small

Check terminal voltage, increase

operating voltage

Maintenance

Code
Text message

Cause

Rectification

M500
Error in the delivery

status

The data could not be restored during

the reset to delivery status

Repeat reset
Load XML file with transmitter data

into the transmitter

M501
Error in the delivery

status

Hardware error EEPROM

Send transmitter for repair

M504
Error at a device

interface

Hardware defect

Check connections
Exchanging the electronics
Send transmitter for repair

M505
No echo available

Transmitter does not detect an echo

during operation
Antenna dirty or defective

Clean the antenna
Use a more suitable antenna/

transmitter
Remove possible false echoes
Optimize transmitter position and

orientation

M507
Error in the

transmitter settings

Error during setup
Error when carrying out a reset
Auto false echo suppression faulty

Carry out reset and repeat setup

M508
No executable

Bluetooth software

Checksum error in Bluetooth software Carry out software update

M509
Software update

running

Software update running

Wait until software update is finished

M510
No communication

with the main

controller

Communication between main

electronics and display module

disturbed

Check the connection cable to the

display
Send transmitter for repair

SITRANS LR140

Operating Instructions, 08/2020,

A5E50352144

Содержание SITRANS LR140



























































Результаты поиска

Содержание SITRANS LR140

Отзывы:

Похожие инструкции для SITRANS LR140

Бренды по названию

Популярные бренды

Siemens SITRANS LR140, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS LR140

Отзывы:

Похожие инструкции для SITRANS LR140

Бренды по названию

Популярные бренды