Siemens SITRANS LR140 Скачать руководство пользователя страница 39

Страница: 39 / 58

Diagnostics and troubleshooting
9.4 Status messages according to NE 107

Code
Text message

Cause

Rectification

no measured value

available

Clean the antenna system

F017
Adjustment span too

small

Adjustment not within specification

Change adjustment according to the

limit values (difference between min.

and max. ≥ 10 mm)

F025
Error in the

linearization table

Index markers are not continuously

rising, for example illogical value pairs

Check linearization table
Delete table/Create new

F036
No operable software

Checksum error if software update

failed or aborted

Repeat software update
Send transmitter for repair

F040
Error in the

electronics

Limit value exceeded in signal

processing
Hardware error

Restart transmitter
Send transmitter for repair

F080
General software

error

General software error

Restart transmitter

F105
Determine measured

value

The transmitter is still in the start

phase, the measured value could not

yet be determined

Wait for the end of the switch-on

phase
Duration up to 3 minutes depending

on the measurement environment

and parameter settings

F260
Error in the calibration

Checksum error in the calibration

values
Error in the EEPROM

Send transmitter for repair

F261
Error in the

transmitter settings

Error during setup
Auto false echo suppression faulty
Error when carrying out a reset

Repeat setup
Carry out a reset

F265
Measurement

function disturbed

Program sequence of the measuring

function disturbed

Device restarts automatically

Function check

Code
Text message

Cause

Rectification

C700
Simulation active

A simulation is active

Finish simulation
Wait for the automatic end after

60 mins.

SITRANS LR140

Operating Instructions, 08/2020,

A5E50352144

Содержание SITRANS LR140



























































Результаты поиска

Содержание SITRANS LR140

Отзывы:

Похожие инструкции для SITRANS LR140

Бренды по названию

Популярные бренды

Siemens SITRANS LR140, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS LR140

Отзывы:

Похожие инструкции для SITRANS LR140

Бренды по названию

Популярные бренды