manualshive.com logo in svg

Siemens SIRIUS 3RW44, Руководство пользователя


Поделиться
Скачать
background image

 

Diagnostics and messages 

 

8.1 Diagnostics and messages 

3RW44 soft starters 
Manual, 03/2017, NEB535219502000/RS-AB/008 

145

 

Message 

①

 

②

 

③

  Cause/solution 

Temperature sensor short-circuit  

x  x  x  Temperature sensor at terminals T1/T2 has short-circuited. 

Remedy: Check the temperature sensor. 

Temperature sensor wire break 

x  x  x  Temperature sensor at terminals T1/T2 is defective, a cable is not 

connected or no sensor is connected. 

Remedy: Check the temperature sensor or if no sensor is connected: 

deactivate the temperature sensor. 

Temperature sensor overload 

x  x  x  Temperature sensor at terminals T1/T2 has tripped. The motor is 

overheated. 
Remedy: Wait until the motor has cooled down and check the motor if 

necessary. 

Maximum starting time exceeded 

 

x   

The set maximum starting time is shorter than the motor's actual ramp-

up time. 
Remedy: Extend the "max. starting time" parameter, increase the 

current limiting value or check the load connected to the motor to 

determine whether there is a mechanical defect. 

I

e

 limit value exceeded/undershot 

x  x   

Set current limit has been exceeded or undershot, e.g. due to a 

clogged fan filter or by the motor stalling. 
Remedy: Check the cause of current limit violation on the motor/load or 

adjust the limits according to the existing load conditions. 

Ground fault detected 

x  x   

One phase is connected to ground (only possible in bypass mode) 
Remedy: Check connections and wiring. 

Manual mode local connection 

break 

x   

 

The connection to the PC has been interrupted (if control via PC) or no 

key has been pressed (if the motor is key-controlled) for a prolonged 

time (see Settings > Display > Activity monitoring time in chapter 

Selecting display settings (Page 97)). 

Control is handed over to the inputs if these have requested control 

priority. 
Remedy: Connect the PC again or increase the activity monitoring time 

and press a key at regular intervals. 

Impermissible I

e

/CLASS setting 

 

x   

The rated operational current I

e

 set for the motor (chapter Entering the 

motor data (Page 61)) in at least one of the three parameter sets 

exceeds the associated, maximum permissible setting current referred 

to the selected CLASS setting (chapter Selecting motor protection 

settings (Page 94

)). In the case of devices with product version ≥ 

*E07*, the corresponding parameter set (PS) in which the incorrect 

value is to be found is displayed. 

For the maximum permissible settings, see chapter Technical data 

(Page 253).  

If the soft starter is connected in an inside-delta circuit, the motor 

feeder may have been incorrectly wired (chapter 3RW44 in an inside-

delta circuit (Page 221)); as a result, the "Status display/Connection 

type" menu item (chapter Status display (Page 109)) contains 

"Unkn./Fault". 
Remedy: Check the rated operational current set for the motor in all 

three parameter sets, select a lower CLASS setting, or calculate the 

soft starter with a size allowance. In the case of an inside-delta circuit, 

check that the wiring of the motor feeder corresponds to the specified 

circuit diagrams. 

As long as the motor is not activated, it is only a status message. 

However, the message becomes a fault without restart if a start 

command is issued. 

Содержание SIRIUS 3RW44





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIRIUS 3RW44

ABB FPBA-01 PROFIBUS DP Quick Installation And Start-Up Manual preview
FPBA-01 PROFIBUS DP
Бренд: ABB Страницы: 2
ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Бренд: ABB Страницы: 4
Samson 3253 Translation Of Original Instructions preview
3253
Бренд: Samson Страницы: 92
Jafar 2901 Operation And Maintenance Manual preview
2901
Бренд: Jafar Страницы: 10
ZETRON MAX Connection Manual preview
MAX
Бренд: ZETRON Страницы: 3
Abus HomeTec Pro CFF3000 Operation preview
HomeTec Pro CFF3000
Бренд: Abus Страницы: 13
NAVITAS 440A Installation & Service Manual preview
440A
Бренд: NAVITAS Страницы: 7
Abus PLHA10000 Quick Manual preview
PLHA10000
Бренд: Abus Страницы: 2
Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Бренд: Bartlett Страницы: 5
Rane DR1 Dimensions And Specifications preview
DR1
Бренд: Rane Страницы: 2
Parker SciLog DINCon Installation, Operating, & Maintenance Instructions preview
SciLog DINCon
Бренд: Parker Страницы: 42
Vizio Xrt302 Manual preview
Xrt302
Бренд: Vizio Страницы: 65
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Бренд: TEL Страницы: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Бренд: Vimar Страницы: 32
hotset C 148 Quick Start Manual preview
C 148
Бренд: hotset Страницы: 2
Cooper S225-50-45 Service Information preview
S225-50-45
Бренд: Cooper Страницы: 4
Trenz Electronic TE0726 Manual preview
TE0726
Бренд: Trenz Electronic Страницы: 21
Nautronic NAUCON-40 User Manual preview
NAUCON-40
Бренд: Nautronic Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды