Siemens SIRIUS 3RW44 Скачать руководство пользователя страница 143

Страница: 143 / 292

Diagnostics and messages

8.1 Diagnostics and messages

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

143

Message

①

②

③

Cause/solution

Phase failure L3

Option 1: Phase L3 is missing or fails/collapses when the motor is in

operation.

Tripped as a result of a dip in the permissible rated operational voltage

> 15 % for > 100 ms during the startup process or > 200 ms in bypass

mode.
Remedy: Connect L3 or rectify the voltage dip.
Option 2: A motor that is not powerful enough is connected and the

fault occurs as soon as a switchover is made to bypass mode.
Remedy: Set the correct rated operational current for the connected

motor or set it to the minimum value (if the motor current is less than

10 % of the set I

, the motor cannot be operated with this starter).

Option 3: Starter used in IT system with ground-fault monitoring

3RW44, product version < *E06* and the PROFIBUS DP

communication module must not be used in this network configuration.
Remedy:

Replace starter with 3RW44, product version ≥ *E07*. Here,

use in combination with the PROFIBUS DP communication module is

admissible. However, the phase voltage values (UL-N) and phase-to-

phase voltage values (UL-L) may be displayed incorrectly on the

measured value display of the 3RW44.

Missing load phase T1

Motor phase T1 is not connected.
Remedy: Connect the motor properly.

Missing load phase T2

Motor phase T2 is not connected.
Remedy: Connect the motor properly.

Missing load phase T3

Motor phase T3 is not connected.
Remedy: Connect the motor properly.

Supply voltage below 75 %

Control supply voltage is less than 75% of the required rated voltage for

more than 100 ms (voltage failure, voltage dip, incorrect control supply

voltage).
Remedy: Check the control supply voltage.

Supply voltage below 85%

Control supply voltage is less than 85 % of the required rated voltage

for more than 2 s (voltage failure, voltage dip).
Remedy: Check the control supply voltage.

Supply voltage above 110%

Control supply voltage is more than 110 % of the required rated voltage

for more than 2 s (voltage peaks, incorrect control supply voltage).
Remedy: Check the control supply voltage.

Current unbalance exceeded

x x

The phase currents are asymmetrical (unbalanced load). Message is

output when the asymmetry is greater than the set limit (parameter:

Current asymmetry limit value).
Remedy: Check the load or modify the parameter value.

Thermal motor model overload

x x x The thermal motor model has tripped. After an overload trip, restarting

is inhibited until the recovery time has elapsed.
Remedy in the event of unwanted tripping:

•

Check whether the motor's rated operational current I

is set

correctly, or

•

Change the CLASS setting, or

•

Possibly reduce the switching frequency, or

•

Deactivate the motor protection (CLASS OFF)

Содержание SIRIUS 3RW44





































































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW44, Руководство пользователя

Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды