Siemens SIRIUS 3RW44 Скачать руководство пользователя страница 155

Страница: 155 / 292

PROFIBUS DP communication module

9.3 Installing the PROFIBUS DP communication module

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

155

Proceed as follows:

Step

Description

Slide a small screwdriver into the

opening of the cover of the

3RW44 soft starter (1). Gently

press the screwdriver downwards

(2) and remove the cover (3).

Insert the PROFIBUS DP

communication module into the

device (4).
Screw the PROFIBUS DP

communication module into place

using screws included in the

scope of supply (5).
Insert the PROFIBUS DP

connecting cable into the socket

of the communication module (6).

Screw the PROFIBUS connecting

cable firmly into place.
Switch on the power supply.

The "BUS" LED flashes yellow.

This means that the

communication module has been

inserted correctly, but has not yet

been activated.

Содержание SIRIUS 3RW44





































































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW44, Руководство пользователя

Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды