Siemens SIREMOBIL Iso-C SP Скачать руководство пользователя

Страница: 9 / 16

Area dose product measurement device

Siemens AG

SPR2-230.033.04

Page 9 of 16

SIREMOBIL Iso-C

Medical Engineering

Rev. 03

06.05

CS PS 24

Installation

•

Disconnect the SIREMOBIL power plug.

•

Remove the SIREPHOS cover.

Without the laser targeting device:

•

Attach the area dose product measurement device to the SIREPHOS using the screws
included in the packaging.

•

Connect the interface cable already integrated in the cable harness to the area dose
product measurement device and lock it in place.

•

Refit the SIREPHOS cover hood and seal the joints with silicone sealing compound.

With the laser targeting device:

•

Remove the laser targeting device from the SIREPHOS by removing the screws.

•

Mount the area dose product measurement device to the SIREPHOS.

•

Reattach the laser targeting device.

•

Connect the interface cable already integrated in the cable harness to the area dose
product measurement device and lock it in place.

•

Check the laser targeting device according to the adjustment instructions and, if
necessary, adjust it.

•

Refit the SIREPHOS cover hood and seal the joints with silicone sealing compound.

Содержание SIREMOBIL Iso-C SP

















Результаты поиска

Содержание SIREMOBIL Iso-C SP

Отзывы:

Похожие инструкции для SIREMOBIL Iso-C SP

Бренды по названию

Популярные бренды

Siemens SIREMOBIL Iso-C SP, Инструкция по установке и настройке

Результаты поиска

Содержание SIREMOBIL Iso-C SP

Отзывы:

Похожие инструкции для SIREMOBIL Iso-C SP

Бренды по названию

Популярные бренды