manualshive.com logo in svg

Siemens SIREMOBIL Iso-C SP, Инструкция по установке и настройке

Поделиться
Скачать
Siemens SIREMOBIL Iso-C SP Скачать руководство пользователя страница 16

SIREMOBIL Iso-C

 

SPR2-230.033.04

Page 16 of 16

Siemens AG

 

Rev. 03

06.05

CS PS 24

Medical Engineering

16

Area dose product measurement device

 

Concluding steps

1

•

Reinstall all the covers.

•

Perform the protective conductor measurement as specified in ARTD-002.731.17.

•

Observe the information on protective conductor testing in these instructions.
Perform the protective conductor test according to ARTD-002.731.17.

¹

The protective conductor resistance may not exceed 0.2 Ohms.

•

Perform partial acceptance tests in accordance with country-specific regulations.

Changes to previous version

1

Entire instructions extended to SIREMOBIL Compact L as from serial number 3000.

Safety information newly inserted.

Required measuring equipment and auxillary devices revised.

Check of the programmed values revised.

Check of the accuracy of the area dose product measuring instrument revised.

Содержание SIREMOBIL Iso-C SP

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды