background image

Introduction

1.4 Decommissioning and Disposal

1.4

Decommissioning and Disposal

Proper decommissioning and disposal of this device is important to prevent malicious

users from obtaining proprietary information and to protect the environment.

Decommissioning

This device may include sensitive, proprietary data. Before taking the device out of

service, either permanently or for maintenance by a third-party, make sure it has

been fully decommissioned.
For more information, refer to the associated 

Configuration Manual

.

Recycling and Disposal

For environmentally friendly recycling and disposal of this device and related

accessories, contact a facility certified to dispose of waste electrical and electronic

equipment. Recycling and disposal must be done in accordance with local

regulations.

1.5

Cabling Recommendations

Siemens recommends using SIMATIC NET industrial Ethernet shielded cables for all

Ethernet ports.

1.5.1

Protection On Twisted-Pair Data Ports

All copper Ethernet ports on RUGGEDCOM products include transient suppression

circuitry to protect against damage from electrical transients and conform with

IEC 61850-3 and IEEE 1613 Class 1 standards. This means that during a transient

electrical event, communications errors or interruptions may occur, but recovery is

automatic.
Siemens also does not recommend using copper Ethernet ports to interface with

devices in the field across distances that could produce high levels of ground

potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions.

1.5.2

Supported Fiber Optic Cables

The following fiber optic cable types are supported under the stated conditions.

Distance (m)

Cable Type

Wavelength (nm) Modal Bandwidth

(MHz·km)

100Base-FX

1000Base-SX

10GBase-SR

850

200

275

33

OM1 (62.5/125)

1300

500

2000

OM2 (50/125)

850

500

550

82

RUGGEDCOM RS400

Installation Manual, 01/2021, C79000-G8976-1016-11

5

Содержание SIMATIC NET RUGGEDCOM RS400

















































Отзывы: