Siemens SIMATIC IPC627E Скачать руководство пользователя

Страница: 60 / 164

Operating the device

5.3 Operating RAID systems

SIMATIC IPC627E

Operating Instructions, 12/2018, A5E44297201-AA

5.3

Operating RAID systems

5.3.1

Display of a defective drive of a RAID system

A defective drive is displayed in conjunction with RAID at the following locations:

●

SIMATIC IPC DiagBase or SIMATIC IPC DiagMonitor monitoring software

●

For onboard RAID system:
"Intel® Rapid Storage Technology", see "Monitoring the onboard RAID system with

"Intel® Rapid Storage Technology" (Page 62)".

5.3.2

RAID1 system: Installation options for drives

The two hard drives required for a RAID1 system can be installed in SIMATIC IPC627E in

the following locations:

●

For onboard RAID system:
–

"Drives (Page 79)"

5.3.3

Configure the onboard RAID system

If you have ordered a device with an onboard RAID system, the RAID system is already

configured on delivery.
If you subsequently set up an onboard RAID system, you will still have to configure it.

Requirements

●

The drives required for the onboard RAID system are built into the device, see:
–

RAID1 system: Installation options for drives (Page 60)

Navigation in the firmware of the onboard RAID system

Action

Button

•

Select entry (then confirm selection)

•

Arrow buttons on the keyboard

•

Confirm selection

•

<Return> button

•

Back to the previous screen

•

<Esc> button

Содержание SIMATIC IPC627E





































































































































































Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC627E, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды