Siemens SIMATIC IPC627E Скачать руководство пользователя

Страница: 39 / 164

Installing and connecting the device

3.2 Installing the device

SIMATIC IPC627E
Operating Instructions, 12/2018, A5E44297201-AA

3.2

Installing the device

3.2.1

Installation guidelines

Procedure during installation and mounting

WARNING

Dangerous voltage and fire hazard
Improper actions during installation and assembly may lead to personal injury and/or

substantial damage to equipment.
You should observe the installation and assembly notes under:

•

Notes on mounting (Page 30)

•

Notes on ambient and environmental conditions (Page 30)

Securing the device

NOTICE
Insufficient load carrying capacity
If the wall it is mounted on does not have a sufficient load-bearing capacity, the device may

fall and be damaged.

•

Ensure that the mounting surface on the wall can bear four times the total weight of the

device, including fixing elements.

NOTICE
Incorrect fixing elements
The device may not be securely fitted if you use screws other than those specified below

for mounting. The device can fall and may be damaged.

•

Use only the specified screws.

Содержание SIMATIC IPC627E





































































































































































Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC627E, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC627E

Отзывы:

Похожие инструкции для SIMATIC IPC627E

Бренды по названию

Популярные бренды