Siemens SENTRON 7KT PAC1600 Series Скачать руководство пользователя страница 63

Страница: 63 / 76

7KT multimeter
Manual, 08/2018, 2514284149-01

Service and maintenance

The device has been calibrated by the manufacturer before shipping. Recalibration is not

required provided the environmental conditions are maintained.

7.1

Firmware update

A firmware update is not possible.

7.2

Fault elimination measures

Fault

Measures

Device is not working.

•

Check power supply connection.

•

Check fuse.

Voltage or current measured values are not dis-

played.

•

Check fuse.

•

Check configuration. You can find more in-

formation under Parameterizing with

powerconfig (Page 50).

Voltage values are not plausible.

Check that the measuring voltages are connected

correctly.
In the case of voltage transformers, ensure that

transformer ratios are set correctly.

Current values are not plausible.

Check the settings and the wiring of the current

transformers and correct if necessary.

No communication.

Check communication settings.

Power values are incorrect, although voltage and

current are correctly applied.

•

Check voltages and currents of the phases to

ensure that they are properly connected to

one another.

•

Check the polarity of the current transformers.

Содержание SENTRON 7KT PAC1600 Series













































































Результаты поиска

Содержание SENTRON 7KT PAC1600 Series

Отзывы:

Siemens SENTRON 7KT PAC1600 Series, Руководство пользователя, Страница: 63 / 76

Результаты поиска

Содержание SENTRON 7KT PAC1600 Series

Отзывы: