Siemens SENTRON 7KT PAC1600 Series Скачать руководство пользователя страница 43

Страница: 43 / 76

7KT multimeter
Manual, 08/2018, 2514284149-01

Connecting

Safety instructions

DANGER

Risk of death due to hazardous voltage!
Before starting work, disconnect the system and the device from the power supply.

DANGER

Risk of death due to electric shock and arc flashover!
For the 5 A device, it is only possible to measure the current via external current

transformers. When using the current transformers, the circuit is not protected by a fuse.

•

Switch off and lock out all power supplying this equipment before working on the device.

•

Never open the secondary circuit of the current transformer under load.

•

Short-circuit the secondary current terminals of the current transformer before removing

this device.

•

Always follow the safety instructions for the current transformers used.

WARNING

Possible risk of death due to damaged device!
Using devices when they are damaged may result in death, serious injury, or property

damage.

•

Do not install damaged devices.

•

Never start up damaged devices.

NOTICE
Equipment damage due to lack of fusing
Non-fused voltage measuring inputs may lead to device and equipment damage.
Always protect the device with an IEC approved fuse or with an IEC approved miniature

circuit breaker.

Содержание SENTRON 7KT PAC1600 Series













































































Результаты поиска

Содержание SENTRON 7KT PAC1600 Series

Отзывы:

Siemens SENTRON 7KT PAC1600 Series, Руководство пользователя, Страница: 43 / 76

Результаты поиска

Содержание SENTRON 7KT PAC1600 Series

Отзывы: