Siemens SENTRON 7KT PAC1600 Series Скачать руководство пользователя страница 38

Страница: 38 / 76

Description

3.4 Parameterization

7KT multimeter

Manual, 08/2018, 2514284149-01

3.4.7

Command menu

The command menu allows you to perform occasional operations (e.g. to reset measured

variables and counters).
After entering the password for the extended level, you can also use the command menu to

perform automatic operations which are useful for the configuration of the device.
The following functions are available in the command menu, separated according to the

required access level.

Code

Command

Access level

Description

C.01

RESET HI-LO

User lev-

el/administrator

Resets the HI and LO values of all measurements.

C.02

RESET MAX DEMAND

Resets the maximum demand values for all meas-

urements.

C.03

RESET PAR.ENERGY

Resets the partial energy meters.

C.04

RESET PAR.HOURS

Resets the partial hour counters.

C.07

RESET ALARMS

Resets alarms.

C.08

RESET LIMITS

Resets limit values

C.11

RESET TOT.ENERGY
(Not with MID devices)

Administrator

Resets the total and partial energy meters.

C.12

RESET TOT.HOURS

Resets the total hour counter.

C.13

SETUP TO DEFAULT

Restores all the factory settings for the device.

C.14

BACKUP SETUP

Saves a backup copy of all setup parameters.

C.15

RESTORE SETUP

Loads the settings from the backup copy.

C.16

WIRING TEST

Runs the test to check whether the device is connect-

ed correctly.
You can find more information in chapter Wiring test

(Page 37).

Select the required command.

Press to execute the command.

Press again to execute the command.

Press to cancel execution of the command.

Press to exit the command menu.

Содержание SENTRON 7KT PAC1600 Series













































































Результаты поиска

Содержание SENTRON 7KT PAC1600 Series

Отзывы:

Siemens SENTRON 7KT PAC1600 Series, Руководство пользователя, Страница: 38 / 76

Результаты поиска

Содержание SENTRON 7KT PAC1600 Series

Отзывы: