Siemens SDV7-AR Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 56

background image

47

Ordering replacement parts

When ordering replacement parts for a
Siemens distribution circuit breaker, it is very
important to give complete information. This
information should include:

1. Type SDV7-AR distribution circuit breaker

serial number listed on circuit breaker
nameplate.

2. Type of operator listed on operator

nameplate.

3. Type of circuit breaker.

4. Rated continuous current of circuit

breaker.

5. Rated voltage of circuit breaker.

6. Description of part. Use instruction book

description insofar as possible.

7. Instruction book number listed on circuit

breaker nameplate.

8. Instruction book item number.

9. Number of pieces required.

While the circuit breaker can be identified by
the serial number alone, all additional
information that is given will serve as a check
to be certain that the part or parts furnished
are correct for the circuit breaker in question.
Without this serial number, Siemens cannot
be sure of the correct identity of the desired
parts.

If any doubt exists as to the instruction book
reference number or the description, a
dimensional sketch of the desired part will
help to properly identify it.

Siemens recommends that a supply of repair
parts be kept on hand so that emergency
repairs can be made without waiting for
shipment of parts from the factory.

A list of recommended spare parts is sent
with the circuit breaker. Before removing any
part to be replaced, observe its function and
adjustment. This usually saves adjustment
time during installation.

«
...
45
46
47
48
49
...
»

Содержание SDV7-AR

























































Отзывы:

Нет отзывов

Похожие инструкции для SDV7-AR

PKZMO-0,16/XTPRP16BC1

Бренд: Eaton Страницы: 81

Бренд: CBS ArcSafe Страницы: 8

Бренд: CBS ArcSafe Страницы: 39

Бренд: ABB Страницы: 34

Бренд: Dateq Страницы: 12

Бренд: Vanguard Instruments Страницы: 18

Бренд: Eaton Страницы: 2

140M-C-AFA Series

Бренд: Allen-Bradley Страницы: 2

Бренд: Allen-Bradley Страницы: 8

Бренд: Allen-Bradley Страницы: 6

Бренд: Allen-Bradley Страницы: 7

Бренд: Allen-Bradley Страницы: 8

Бренд: Allen-Bradley Страницы: 37

Бренд: Amphenol Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды