Siemens SDV7-AR Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 56

background image

29

c) Press black Close pushbutton (53.0).

d) Verify main contact status indicator

shows CLOSED.

e) Press red Open pushbutton (54.0)

again.

f) Verify main contact status indicator

shows OPEN.

5. De-energize the control power by opening

the control power disconnect device in
the relay and control compartment.
Remove the mechanism housing cover
sheet (60.1). Do not unplug connector
(106.3) from the capacitor boards, or
damage to the capacitor board or the
controller board may occur. Fast discharge
the capacitors (106.2) by unplugging the
connector (105.2) on the capacitor
controller board (105.0). During fast
discharge of the capacitors, a red LED on
each capacitor board will flash, indicating
that discharge is in process. The process is
complete when the red LED stops
blinking.

6. After the discharging process is complete,

plug in the connector (105.2) to the
controller board (105.0).

External manual trip

1. Energize control power circuit by closing

the control power disconnect device
shown in Figure 8: Relay and control and
operator compartments for type SDV7-
MA-AR circuit breaker with magnetic-
actuator operator on page 30. The LEDs
(105.1) should show the progress of
capacitor charging.

2. Use the Close pushbutton on the circuit

breaker operating mechanism (refer to
Figure 7: Operator controls and

discharging capacitors on page 26) to
close the circuit breaker.

3. Use the manual opening handle on the

right side of the enclosure (refer to Figure
8: Relay and control and operator
compartments for type SDV7-MA-AR
circuit breaker with magnetic-actuator
operator on page 30) to open the circuit
breaker.

4. Attempt to close the circuit breaker using

the pushbutton on the circuit breaker
operating mechanism (refer to Figure 7:
Operator controls and discharging
capacitors on page 26). The circuit
breaker should not close.

5. Reset the manual opening handle to

NORMAL position by pulling the retainer
pin out.

6. After resetting the manual opening

handle to NORMAL position, attempt to
close the circuit breaker using the
pushbutton on the circuit breaker
operating mechanism. The circuit breaker
should close.

7. Open the circuit breaker using the

pushbutton on the circuit breaker
operating mechanism.

8. Open control power circuit by opening

control power disconnect shown in Figure
8: Relay and control and operator
compartments for type SDV7-MA-AR
circuit breaker with magnetic-actuator
operator on page 30.

Final mechanical inspection and testing
without control power

Before the circuit breaker is energized, it must
be thoroughly inspected and tested. Correct
any deviations before energization.

Spring-loaded mechanism.

Can result in moderate injury.

When handle is in TRIP or CLOSE BLOCKED positions, pulling release pin
causes handle to return to NORMAL position very rapidly. Keep hand clear of
handle when pulling release pin.

«
...
27
28
29
30
31
...
»

Содержание SDV7-AR

























































Отзывы:

Нет отзывов

Похожие инструкции для SDV7-AR

Masterpact MP-MC

Бренд: Merlin Gerin Страницы: 24

Бренд: nader Страницы: 20

EntelliGuard AKR30S-800A

Бренд: GE Страницы: 64

Cutler-Hammer VCP-W

Бренд: Eaton Страницы: 48

GE Power Break II

Бренд: ABB Страницы: 2

Бренд: Dateq Страницы: 12

Бренд: Moeller Страницы: 2

Бренд: ABB Страницы: 72

Бренд: Schrack Страницы: 2

Бренд: Schrack Страницы: 3

Бренд: Schrack Страницы: 4

Бренд: Schrack Страницы: 5

Бренд: Sigma Страницы: 20

Бренд: LEGRAND Страницы: 5

Бренд: LEGRAND Страницы: 4

Бренд: LEGRAND Страницы: 8

Бренд: LEGRAND Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды