Siemens SDV7-AR Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 56

background image

27

Hazardous voltages and stored energy.

Will cause death, serious injury or property damage.

Even if the circuit breaker and control circuits have been de-energized for a
long time, the power supply capacitors will maintain significant stored
energy. Always discharge the capacitors before maintenance. Always de-
energize and ground the equipment before maintenance.

Read and understand this instruction manual before using equipment.
Maintenance should be performed only by qualified personnel. The use of
unauthorized parts in the repair of the equipment or tampering by
unqualified personnel will result in dangerous conditions which will cause
death, severe injury or equipment damage. Follow all safety instructions
contained herein.

Stored energy and high speed moving parts.

Will result in serious injury. Fingers can be crushed by the magnetic
actuator.

Do not remove guard panel. Do not operate circuit breaker if guard panel
removed.

Discharging capacitors

After control power has been removed,
discharge stored energy from the capacitors
(refer to Figure 7: Operator controls and
discharging capacitors.

1. Press red Open pushbutton (54.0).

2. Remove the mechanism housing cover

sheet (60.1).

3. Discharge the capacitors (106.2) by

unplugging the connector (105.2) from
the controller board (105.0). The red LED
(106.4) on each of the capacitor boards
(106.1) indicates the state of charge of
the capacitors (106.2). When the
capacitors (106.2) are discharging, the
red LEDs are flashing. This indicates a
hazardous voltage. When the LEDs stop
flashing, the capacitors (106.2) are
discharged to a low voltage.

Automatic capacitor charging

The controller board (105.0) executes a self-
test of the capacitors (106.2) and checks the
status of the capacitors (106.2). This self-test
runs automatically and regularly. The result of
the self-test is stored in the memory of the
controller board (105.0).

«
...
25
26
27
28
29
...
»

Содержание SDV7-AR

























































Отзывы:

Нет отзывов

Похожие инструкции для SDV7-AR

Бренд: Eaton Страницы: 12

BC160NT305 Series

Бренд: OEZ Страницы: 17

Бренд: Toshiba Страницы: 38

Бренд: Toshiba Страницы: 39

Бренд: Toshiba Страницы: 57

Бренд: Toshiba Страницы: 59

Бренд: Toshiba Страницы: 63

Бренд: Stahl Страницы: 52

DEHNvario DVR BNC RS485 230

Бренд: dehn Страницы: 4

Бренд: nader Страницы: 39

Бренд: GE Страницы: 63

Бренд: Eaton Страницы: 62

Moeller DIL-SWD-32-001

Бренд: Eaton Страницы: 2

Бренд: Merlin Страницы: 28

Бренд: Testboy Страницы: 16

Бренд: Apator Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды