Siemens SCALANCE X101-1 Скачать руководство пользователя страница 34

Страница: 34 / 86

Product Characteristics

4.3 SCALANCE X101-1FL

4.3.7

SCALANCE X101-1FL Button

What is the function of the button?

Using the button , you can display and modify the set fault mask.

After continuously pressing the button, the currently valid fault mask is displayed for

approximately 3 seconds. The LED of the monitored port flashes at a frequency of 5 Hz.

Keep the button pressed to modify the fault mask. After another 3 seconds, the current link

status of the ports and the indicator of the power supply LEDs are displayed at a flashing

frequency of 2.5 Hz. Keep the button pressed. After another 3 seconds, this status is applied

as new fault mask and saved. The now monitored ports are indicated by the permanently lit

LEDs until the button is released. As long as the LEDs are still flashing, the saving can be

canceled by releasing the button.

If an empty fault mask (no port is monitored) is set or is to be set, the 2 port LEDs flash

alternatingly.

Simultaneously with the fault mask, the monitoring of the connected power supply is set. The

existence of the two power supply units is only monitored if both power supplies are

connected during saving the fault mask.

The failure of the link on a monitored port or of one of the monitored power supplies is

indicated by the illuminated red error LED. The signaling contact is opened simultaneously.

Note

The factory default is no port monitoring but monitoring of the power supply L1+/M1. If

necessary, error LED and signaling contact have to be cleared by pressing the button for an

appropriate period or the feeding point has to be changed when connecting only one power

supply to L2+/M2.

The setting remains after turning off/on.

4.3.8

Cascade Connection of two Media Converters

If you cascade two media converters, i.e. connect the converters via the FO port, it is

mandatory to previously activate this operating mode using the button. Keep the button

pressed for 1-2 seconds. After releasing, the acceptance of the operating mode is indicated

by the illuminated

“

”

(transparent link) LED. Again press the button for 1-2 seconds to exit

this operating mode. The

“

”

LED is extinguished.

Important notes:

•

Max. two media converters can be cascaded

•

mixed cascading with SCALANCE X-100 Media converter and OMC-Media

converter is not possible

•

The cascade connection is only permitted via the connection of the FO ports!

Industrial Ethernet Media Converters SCALANCE X-100 Series

4-20

Commissioning Manual, 07/2008, A2B00051521A

Содержание SCALANCE X101-1























































































Результаты поиска

Содержание SCALANCE X101-1

Отзывы:

Похожие инструкции для SCALANCE X101-1

Бренды по названию

Популярные бренды

Siemens SCALANCE X101-1, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SCALANCE X101-1

Отзывы:

Похожие инструкции для SCALANCE X101-1

Бренды по названию

Популярные бренды