Siemens SCALANCE X101-1 Скачать руководство пользователя страница 32

Страница: 32 / 86

Product Characteristics

4.3 SCALANCE X101-1FL

Connectors

The cables are connected to BFOC sockets.

4.3.6

SCALANCE X101-1FL Power Supply and Signaling Contact

Power Supply

The power supply is connected using a 4-pin plug-in terminal block. The power supply can

be connected redundantly. Both inputs are isolated. There is no distribution of load. When

using a redundant power supply, the power supply unit with the higher output voltage

supplies SCALANCE X101-1FL alone. The power supply is connected over a high

resistance with the enclosure to allow an ungrounded setup.

Figure

4-9

Power supply SCALANCE X101-1FL

Figure

4-10

Connector pinout

Pin number Pinout
Pin 1

L1+ (+18 - 32V DC)

Pin 2

M1 (ground)

Pin 1

M2 (ground)

Pin 2

L2+ (+18 - 32V DC)

Warning
The SCALANCE X101-1FL device is designed for operation with safety extra-low voltage.

This means that only safety extra-low voltages (SELV) complying with IEC950/EN60950/

VDE0805 can be connected to the power supply terminals.

The power supply unit to supply SCALANCE X101-1FL must comply with NEC Class 2

(voltage range 18-32 V, current requirement 200 mA).

If the device is connected to a redundant power supply (two separate power supplies), both

must meet these requirements.

The signaling contact can be subjected to a maximum load of 100 mA (safety extra-low

voltage (SELV), DC 24 V).

Never connect SCALANCE X101-1FL to AC voltage.

Never operate SCALANCE X101-1FL with DC voltage higher than 32 V DC.

Industrial Ethernet Media Converters SCALANCE X-100 Series

4-18

Commissioning Manual, 07/2008, A2B00051521A

Содержание SCALANCE X101-1























































































Результаты поиска

Содержание SCALANCE X101-1

Отзывы:

Похожие инструкции для SCALANCE X101-1

Бренды по названию

Популярные бренды

Siemens SCALANCE X101-1, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SCALANCE X101-1

Отзывы:

Похожие инструкции для SCALANCE X101-1

Бренды по названию

Популярные бренды