Siemens SCALANCE X-100 Скачать руководство пользователя страница 24

Страница: 24 / 78

Description of the device

3.5 LED display

SCALANCE X-100

Operating Instructions, 12/2016, A2B00060666-08

3.5

LED display

Fault LED "F" (red LED)

The fault LED indicates the incorrect functioning of the device.

LED color

LED status

Meaning

Red

Lit

The IE switch detects an error. At the same time, the signaling contact opens.
The following faults/errors are detected:
1.

Link down event on a monitored port.

Loss of the power supply of one of the two redundant power supplies or the pow-

er supply drops below 9.6 V.

Both power supplies are below approximately 9.6 V (voltage too low).

Off

No error detected.

Power LEDs “L1” and “L2” (green LEDs)

The power LEDs show the status of the power supply at connectors L1 and L2.

L1/L2 LEDs

L1/L2 connector

LED color

LED status

Green

Lit

Power supply L1 or L2 is connected.

Off

Power supply L1 and L2 are not connected or L1 and L2 <9.6 V.

Note
If the green LED is not lit, no other signal LED lights up either.

Port LEDs "P" (green/yellow LEDs)

The port LEDs indicate the status of the ports.

LED color

LED status

Meaning

Green

Lit

Link exists, no data reception at port

Yellow

Lit

Link exists, data reception at port

Yellow

Flashing

Setting or display of the fault mask

Содержание SCALANCE X-100















































































Результаты поиска

Содержание SCALANCE X-100

Отзывы:

Похожие инструкции для SCALANCE X-100

Бренды по названию

Популярные бренды

Siemens SCALANCE X-100, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X-100

Отзывы:

Похожие инструкции для SCALANCE X-100

Бренды по названию

Популярные бренды