Siemens SCALANCE W734-1 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 64

background image

Description of the device

3.6 Reset button

SCALANCE W774-1 /W734-1
Operating Instructions, 01/2017, C79000-G8976-C325-08

25

Functions of the reset button

The reset button has the following functions:

●

Restart of the device
To restart the device, press the Reset button briefly.

Note
If you make changes to the configuration and restart immediately afterwards with the

reset button, the changes may be lost. If you restart the device using the WBM (menu

command "System > Restart") or using the CLI (command "restart" in the Privileged

EXEC Modus), the configuration changes are always retained.

Upkeep and maintenance

●

Loading new firmware
If the "Load & Save" menu command of Web Based Management is unsuccessful, the

reset button can be used to load new firmware. This situation can occur if there is a

power outage during the normal firmware update. You will find further information in the

configuration manual in Downloading new firmware using TFTP without WBM and CLI.

●

Resetting the device to the factory defaults
The device can be reset to the factory defaults during operation. You will find more

detailed information in the configuration manual in Resetting the device to factory

defaults.

NOTICE
Previous settings
If you reset, all the changes you have made will be overwritten by factory defaults.

NOTICE
Inadvertent reset
An inadvertent reset can cause disturbances and failures in the configured network with

further consequences.

«
...
23
24
25
26
27
...
»

Содержание SCALANCE W734-1

































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE W734-1

Бренд: LevelOne Страницы: 14

Бренд: sauter Страницы: 8

Бренд: iBall Baton Страницы: 61

Бренд: Modecom Страницы: 48

Бренд: Abocom Страницы: 37

Бренд: Vaisala Страницы: 76

Бренд: Obihai Страницы: 4

Бренд: Linksys Страницы: 123

Бренд: Billion Страницы: 2

WatchDog 3388BC

Бренд: Spectrum Technologies Страницы: 10

Бренд: Gigafast Страницы: 24

FRITZ! Powerline 1260E

Бренд: AVM Страницы: 44

Бренд: 4gon Страницы: 88

Бренд: Sapido Страницы: 54

Бренд: NX Страницы: 32

Бренд: Jabra Страницы: 2

Wireless access point

Бренд: LEGRAND Страницы: 32

Бренд: K3C Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды