Siemens SCALANCE W734-1 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 64

background image

Connection

5.1 Lightning protection, power supply and grounding

SCALANCE W774-1 /W734-1

36

Operating Instructions, 01/2017, C79000-G8976-C325-08

5.1

Lightning protection, power supply and grounding

Lightning protection

WARNING

Danger due to lightning strikes
Antennas installed outdoors must be within the area covered by a lightning protection

system. Make sure that all conducting systems entering from outdoors can be protected by

a lightning protection potential equalization system.
When implementing your lightning protection concept, make sure you adhere to the VDE

0182 or IEC 62305 standard.

Suitable lightning protectors are available in the accessories (Page 15) of SIMATIC NET

Industrial WLAN.

Note
We recommend that you use the maintenance-free lightning protector LP798-2N.
Exception: When there is also DC power supplied via the antenna cable. In this case, only

the lightning protector LP798-1N can be used.

WARNING

Danger due to lightning strikes
Installing this lightning protector between an antenna and a SCALANCE W700 is not

adequate protection against a lightning strike. The LP798-1N lightening protector only

works within the framework of a comprehensive lightning protection concept. If you have

questions, ask a qualified specialist company.

Note
The requirements of EN61000-4-5, surge immunity tests on power supply lines, are met only

when a Blitzductor is used with 24 VDC:
BVT AVD 24

type no. 918 422

Manufacturer: DEHN+SÖHNE GmbH+Co.KG, Hans Dehn Str. 1, Postfach 1640, D -

92306 Neumarkt, Germany

«
...
34
35
36
37
38
...
»

Содержание SCALANCE W734-1

































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE W734-1

Бренд: Laird Страницы: 24

Бренд: Laird Страницы: 6

Бренд: T-Mobile Страницы: 8

Бренд: T-Mobile Страницы: 3

Бренд: D-Link Страницы: 147

Бренд: RAK Страницы: 19

Бренд: Abocom Страницы: 1

7000AP - Air Xpert - Wireless Access Point

Бренд: D-Link Страницы: 8

Бренд: EnGenius Страницы: 2

Бренд: ELTEX Страницы: 22

Бренд: Nanosat Страницы: 11

Бренд: Telstra Страницы: 28

Бренд: SkyLink Страницы: 4

Бренд: LINK LABS Страницы: 14

airFiber AF-11FX

Бренд: Ubiquiti Страницы: 47

Бренд: Draytek Страницы: 1

Бренд: Draytek Страницы: 2

Бренд: BroadMobi Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды