Siemens SCALANCE W734-1 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 64

background image

Connection

5.4 Antenna connectors

SCALANCE W774-1 /W734-1

44

Operating Instructions, 01/2017, C79000-G8976-C325-08

5.4

Antenna connectors

The SCALANCE W774/W734 has two antenna connectors of the type R-SMA located on the

top of the device.

①

Antenna connector R1 A1

②

Antenna connector R1 A2

Procedure

Follow the steps below to connect a cable for an external antenna to a SCALANCE

W774/734:
1.

Insert the connector on the antenna cable into the R-SMA socket and tighten the sleeve

nut of the plug on the socket (key size SW8, tightening torque 1 Nm). If you only use one

antenna, you need to connect this to the device via antenna connector R1 A1 (position

①

).

2.

Screw a terminating resistor to the unused antenna socket R1 R2 (position

②

) if you are

only using one antenna.

NOTICE
UL approval only for use in buildings
Within the area of authority of the NEC and CEC, the SCALANCE W770/W730 devices and

the antennas connected to them may only be used in a closed building. For this reason, do

not lead antennas into the outdoor area if you need to meet UL requirements.

«
...
42
43
44
45
46
...
»

Содержание SCALANCE W734-1

































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE W734-1

Бренд: Wavion Страницы: 66

Бренд: 2N Страницы: 3

DGL-4500 - GamerLounge Xtreme N Gaming Router...

Бренд: D-Link Страницы: 108

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Бренд: D-Link Страницы: 38

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Бренд: D-Link Страницы: 80

DAP-2590 - AirPremier N Dual Band PoE Access...

Бренд: D-Link Страницы: 36

Бренд: Nexxt Страницы: 2

Бренд: Gemtek Systems Страницы: 54

Бренд: Amigo Страницы: 9

Бренд: cramZ Страницы: 20

Бренд: Linksys Страницы: 121

Бренд: Linksys Страницы: 42

Бренд: DeWalt Страницы: 8

Бренд: Zte Страницы: 29

Бренд: Aversky Technology Страницы: 10

Бренд: Billion Страницы: 7

Бренд: H3C Страницы: 69

Бренд: Moxa Technologies Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды