Siemens SCALANCE W734-1 Скачать руководство пользователя страница 17

Страница: 17 / 64

Description of the device

3.4 Accessories

SCALANCE W774-1 /W734-1
Operating Instructions, 01/2017, C79000-G8976-C325-08

Energy cable

Component

Description

Article number

Energy cable 2

x 0.75

Energy cable for connection of signaling contact and power

supply 24 VDC, stranded wire 2 x 0.75 mm

, capable of trail-

ing, not assembled
Sold by the meter

6XV1 812-8A

Robust Energy

Cable 4 x 0.75

Energy cable for connection of power supply 24 VDC, 4-wire

stranded 4 x 0.75 mm

, robust, flexible, not assembled

Sold by the meter

6XV1 801-2A

M12 PLUG-IN

CABLE

Flexible plug-in power cable to connect the power supply 24

VDC, 4-wire, preassembled with a 4-pin M12 plug and an

M12 socket (A-coded)

6XV1 801-5D*

* Available in different lengths

Socket

Component

Description

Article number

IE POWER M12

CABLE CONNECTOR

PRO

Socket for the 24 VDC power supply. 4-pin, A-

coded
pack of 3

6GK1 907-0DC10-6AA3

Lightning protection

Component Description

Article number

LP798-1N Lighting protector with N/N female/female connector with

gas discharge technology

6GK5798-2LP00-2AA6

LP798-2N

Lighting protector with N/N female/female connector with

quarter wave technology

6GK5798-2LP10-2AA6

Terminating resistor

Component Description

Article number

TI795-1N

Electrical connection
N-Connect, male

6GK5795-1TN00-1AA0

Содержание SCALANCE W734-1

































































Результаты поиска

Содержание SCALANCE W734-1

Отзывы:

Siemens SCALANCE W734-1, Руководство по эксплуатации, Страница: 17 / 64

Результаты поиска

Содержание SCALANCE W734-1

Отзывы: