Siemens SCALANCE M812 страница 43 Скачать руководство пользователя | Manualshive

Страница: 43 / 74

background image

WARNING

Lack of equipotential bonding

If there is no equipotential bonding in hazardous areas, there is a risk of explosion due to
equalizing current or ignition sparks.
• Ensure that equipotential bonding is available for the device.

WARNING

Unprotected cable ends

There is a risk of explosion due to unprotected cable ends in hazardous areas.
• Protect unused cable ends according to IEC/EN 60079-14.

WARNING

Improper installation of shielded cables

There is a risk of explosion due to equalizing currents between the hazardous area and the non-
hazardous area.
• Ground shielded cables that cross hazardous areas at one end only.
• Lay a potential equalization conductor when grounding at both ends.

WARNING

Insufficient isolation of intrinsically safe and non-intrinsically safe circuits

Risk of explosion in hazardous areas
• When connecting intrinsically safe and non-intrinsically safe circuits, ensure that the

galvanic isolation is performed properly in compliance with local regulations (e.g. IEC
60079-14).

• Observe the device approvals applicable for your country.

Notes for use in hazardous locations according to ATEX, IECEx, UKEX and CCC Ex
If you use the device under ATEX, IECEx, UKEX or CCC Ex conditions you must also keep to
the following safety instructions in addition to the general safety instructions for protection
against explosion:

WARNING

Transient overvoltages

Take measures to prevent transient overvoltages of more than 40% of the rated voltage (or
more than 119 V). This is the case if you only operate devices with SELV (safety extra-low
voltage).

Connecting up

5.1 Safety when connecting up

SCALANCE M826
Operating Instructions, 10/2022, C79000-G8976-C362-07

43

«
...
41
42
43
44
45
...
»

Содержание SCALANCE M812











































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE M812

Бренд: ABB Страницы: 11

Бренд: Baker Hughes Страницы: 168

Бренд: NAD Страницы: 10

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: Eaton Страницы: 21

Бренд: Eaton Страницы: 70

Бренд: NANO Страницы: 4

Бренд: Xtool Страницы: 51

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: Taurus Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды