Siemens RUGGEDCOM RS910L страница 35 Скачать руководство пользователя

Страница: 35 / 50

Communication Ports
4.3.2 Configuration and Setup

4.3.2

Configuration and Setup

If the RUGGEDCOM RS910L and another device both have Universal EoVDSL ports,

configure one device to be the Master and the other the Slave. If both devices have a

Long-Reach EoVDSL port, no Master/Slave configuration is necessary, since the ports

will already be fixed as Master or Slave.
Once configured and connected together, each device will attempt to achieve the

maximum speed based on the line length and conditions. The RUGGEDCOM RS910L's

Link/Act

LED may flash on and off several times before setting on a final link speed

and declaring the port up.
For more information about configuring the RUGGEDCOM RS910L , refer to the

RUGGEDCOM RS910L User Guide

for the .

4.3.3

EoVDSL Performance

The following describes the behavior and performance characteristics of EoVDSL.

EoVDSL Modes

The EoVDSL port can be configured to operate in one of two modes:
•

Auto Mode (default)

In Auto Mode, the device will step through the different speeds and automatical-

ly select the best bit-rate based on the current line conditions.

•

Manual Mode

In Manual Mode, the user can select one of the speed settings and the device will

only attempt to attain the set speed.

If the line conditions degrade (reducing the SNR or Signal to Noise Ratio), but the de-

vice is able to maintain the link, an alarm will be triggered to notify the user of the

reduced SNR. By configuring the

Rescan Mode

parameter in RUGGEDCOM RS910L,

the user can control at which point the scan process will be restarted when the line

conditions degrade. If

Link only

is selected, the device will restart the scan process

if the line conditions degrade, such that the device is unable to maintain the current

link. If

Link or SNR

is selected, the device will restart the scan process if either the

SNR has dropped below a pre-defined acceptable level or when the device is unable

to maintain the current link, or whichever comes first.

Note

If the

Mode

parameter is set to

Manual Mode

, the restart of the scan process will on-

ly attempt to attain the set speed in manual mode.

For information about configuring EoVDSL, refer to the

RUGGEDCOM RS910L User

Guide for the RUGGEDCOM RS910L

RUGGEDCOM RS910L

Installation Manual, 02/2020, C79000-G8976-1030-06

Содержание RUGGEDCOM RS910L



















































Результаты поиска

Содержание RUGGEDCOM RS910L

Отзывы:

Похожие инструкции для RUGGEDCOM RS910L

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RS910L, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RS910L

Отзывы:

Похожие инструкции для RUGGEDCOM RS910L

Бренды по названию

Популярные бренды