Siemens RUGGEDCOM RS910L страница 32 Скачать руководство пользователя

Страница: 32 / 50

Communication Ports

4.2 Fiber Optic Ethernet Ports

4.2

Fiber Optic Ethernet Ports

Fiber optic Ethernet ports are available with either MTRJ (Mechanical Transfer Reg-

istered Jack), LC (Lucent Connector), SC (Standard or Subscriber Connector) or ST

(Straight Tip) connectors. Make sure the Transmit (Tx) and Receive (Rx) connections

of each port are properly connected and matched to establish a proper link.

Port Types

Tx Connector

Rx Connector

Figure 4.4

MTRJ Port

Tx Connector

Rx Connector

Figure 4.5

LC Port

Tx Connector

Rx Connector

Figure 4.6

SC Port

Tx Connector

Rx Connector

Figure 4.7

ST Port

LEDs

Each port features an LED that indicates the link/activity state of the port.

State

Description

Yellow (Solid)

Link established

Yellow (Blinking)

Link activity

Off

No link detected

Specifications

For specifications on the available fiber optic Ethernet ports, refer to

"Fiber Optic Eth-

ernet Port Specifications (Page 31)"

4.3

EoVDSL Ports

Ethernet over VDSL (EoVDSL) connections operate in pairs with one device config-

ured as the Master and the other as the Slave. In VDSL (Very-high-bit-rate Digital Sub-

RUGGEDCOM RS910L

Installation Manual, 02/2020, C79000-G8976-1030-06

Содержание RUGGEDCOM RS910L



















































Результаты поиска

Содержание RUGGEDCOM RS910L

Отзывы:

Похожие инструкции для RUGGEDCOM RS910L

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RS910L, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RS910L

Отзывы:

Похожие инструкции для RUGGEDCOM RS910L

Бренды по названию

Популярные бренды