Siemens QUADLOG Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 66

Siemens QUADLOG Скачать руководство пользователя страница 65

WARRANTY

The Company warrants all equipment manufactured by it and bearing its nameplate, and all
repairs made by it, to be free from defects in material and workmanship under normal use and
service. If any part of the equipment herein described, and sold by the Company, proves to be
defective in material or workmanship and if such part is within twelve months from date of
shipment from the Company’s factory, returned to such factory, transportation charges prepaid,
and if the same is found by the Company to be defective in material or workmanship, it will be
replaced or repaired, free of charge, f.o.b. Company’s factory. The Company assumes no liability
for the consequence of its use or misuse by Purchaser, his employees or others. A defect in the
meaning of this warranty in any part of said equipment shall not, when such part is capable of
being renewed, repaired or replaced, operate to condemn such equipment. This warranty is
expressly in lieu of all other warranties, guaranties, obligations, or liabilities, expressed or
implied by the Company or its representatives. All statutory or implied warranties other than title
are hereby expressly negated and excluded.

Warranty repair or replacement requires the equipment to be returned to one of the following
addresses:

Equipment manufactured or sold by Siemens Moore Process Automation, Inc.

Siemens Moore Process Automation, Inc.
Sumneytown Pike
Spring House, PA 19477 U.S.A.
Tel: +1 215 646 7400
Fax: +1 215 283 6340

Equipment manufactured or sold by MOORE PRODUCTS CO. (Canada) Inc.

Siemens Moore Process Automation, Inc.
c/o MOORE PRODUCTS CO. (Canada) Inc.
P.O. Box 370
Brampton, Ontario L6V 2L3, Canada
Tel: +1 905 457 9638
Fax: + 1 905 457 4182

Equipment manufactured or sold by MOORE PRODUCTS CO. (UK) LTD.

Siemens Moore Process Automation, Inc.
c/o MOORE PRODUCTS CO. (UK) LTD
Copse Road,
Lufton Industrial Estate
Yeovil, Somerset BA22 8RN, England
Tel: +44 1935 706262
Fax: +44 1935 706969

The warranty will be null and void if repair is attempted without authorization by a member of
the Siemens Moore Process Automation, Inc., Service Department.

n

«
...
63
64
65
66
»

Содержание QUADLOG



































































Отзывы:

Нет отзывов