manualshive.com logo in svg

Siemens QUADLOG, Инструкция по установке и обслуживанию, Страница: 27 / 66

Поделиться
Скачать
Siemens QUADLOG Скачать руководство пользователя страница 27

SD39RIO-1 INSTALLATION 
 

 
 

 

 

 
January 2001 

2-15

2.5.2   IOBUS Cable Connection up to 300 ft. (91 m) 
           for Redundant and Non-Redundant Systems

 

 
This section describes the preparation and installation of IOBUS cables for rack-to-rack redundant or non-
redundant APACS+ or QUADLOG systems when the needed cable length exceeds the maximum standard 
length of 98.4 Feet (30 meters) of a factory-prepared IOBUS cable, but is less than 300 feet (91 meters).  
 
The cable preparation procedure provided here involves splicing a custom-length cable that has unprepared 
ends. This kind of cable is type W2072.  It is intended for use as an IOBUS extension cable between two 
Remote I/O Racks, or between a Remote I/O Rack and another type of rack (e.g., MODULRAC or 
SIXRAC). 
 
The Remote I/O Rack can accommodate either prepared or unprepared ends of available IOBUS cable(s). A 
prepared cable end has a molded connector on it and is to be plugged into the appropriate IOBUS IN or 
IOBUS OUT connector on the rack’s backplane (see Figure 2-4).  The wires emerging from an unprepared 
cable end are to be individually stripped and connected directly to the screw terminals of the associated 
IOBUS IN or IOBUS OUT terminal block, also located on the rack’s backplane (see Figure 2-4).  
 
When another type of rack (e.g., MODULRAC or SIXRAC) is also used, it requires a prepared cable end 
(with a connector) to attach that rack to the IOBUS.  In these instances, you must supply DIN rail-mounted 
style terminal blocks (one for A side and one for B side). The terminal blocks are needed to transition 
between a W2072 unprepared cable end and another cable segment that has a prepared end that is usually 
obtained by cutting a standard IOBUS extension cable in half and preparing the cut end. To modify an 
IOBUS cable in this way, refer to section 2.5.5.  Each user supplied terminal block must be able to 
accommodate wire sizes of 16 to 28 AWG (1,3 mm

2

 to 0.09 mm

2

). 

 

IMPORTANT 

 

It is important to preserve continuous cable impedance through all splice 
connections. This is to minimize signal reflections within the cable and help assure 
collision-free communications. After preparing cable ends, make sure each intended 
pair is re-twisted at the same intervals all the way to the screw terminals of the 
terminal blocks.  Refer to Figures 2-12 and 2-13. 

 
 

To connect a W2072 IOBUS cable between a terminal block and a Remote I/O Rack:

 

 
1.  Determine the length of W2072 cable needed to connect from the terminal block location to the 

appropriate IOBUS connection point on the Remote I/O Rack’s backplane. Allow slack for cable 
stripping, dressing, tagging, and strain relief at each end.  

 
2. At the user-supplied terminal block, provide strain relief for the W2072 cable end. Connect the W2072 

cable conductors (wires) to the terminal block. Wire stripping and color code information for making 
connections are provided in Table 2-1 and Figure 2-11 respectfully. 

 

Содержание QUADLOG



































































Отзывы:

Нет отзывов