Siemens NK8237 MP4.40 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 68

Siemens NK8237 MP4.40 Скачать руководство пользователя страница 54

Maintenance and diagnostics

54

Building Technologies

048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products

06.2011

9

Maintenance and diagnostics

9.1

Kernel update

The NK8237

Kernel

is the main component of the operating system, which acts as

a bridge between the application and the hardware level.

In certain conditions, it may be necessary to update the NK8237 Kernel, following
specific instructions of the technical support. In such cases, you can use the

NK8000Kernel_Update Setup.msi

tool that is available in the

NK8000 - Support

Tools

folder of the DMS8000 CD.

The tool is provided as a Microsoft Installer file (MSI) and can be easily installed on
the Windows system that can connected to the NK8237 unit on the IP network.

Once installed, the

NK8000Kernel_Update

application can be started from the

Windows Start menu. The following window appears:

Fig. 33 Updating NK8237 Kernel

To update the NK8237 Kernel:
1.

Enter the IP address of the NK8237 to update.

2.

Click

Update Kernel

.

At that point, the tool performs a number of preliminary checks. Namely:



It verifies whether the NK8237 firmware is compatible with the new Kernel. If

not, a message will instruct you to download a new firmware and try updating
the Kernel again.



It verifies whether the existing Kernel is older, the same, or newer then the new

Kernel and prompts you to conform the update.

The Kernel update is relatively fast (about 2 min). Make sure not to power off the
NK8237 unit or the Windows computer during the updating procedure.

If needed, you can show the Kernel version by clicking the

About

button. Note that

two Kernel versions are presented that are automatically selected for the
NKM8001-A1 or the NKM8001-A2 mainboard, respectively.

Fig. 34 Showing the Kernel versions

«
...
52
53
54
55
56
...
»

Содержание NK8237 MP4.40





































































Отзывы:

Нет отзывов