Siemens NK8237 MP4.40 Скачать руководство пользователя страница 30

Страница: 30 / 68

Configuration

Building Technologies

048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products

06.2011

7 Configuration

The following picture gives an overview about the configuration workflow.

There are basically three configuration steps:

1. Configure the fire detection with Sinteso Works

(or Cerberus-Engineering-Tool) and download the fire system.
Then, export the configuration in SiB-X format.

2. Configure the NK8237 in Composer and import the SiB-X file.

If requested, the Modbus mapping can be customized. Download the configura-
tion to the NK8237. Export the Modbus mapping table in CSV format.

3. The Modbus device needs to be configured by the integrator based on the

information provided in the Modbus mapping table (CSV export file).

The following chapters describe the configuration steps in detail.

7.1

Configuration checklist

Verify that you have satisfied the items needed in the first checklist before proceed-
ing to the configuration checklist that follows.

The following abbreviations are used the checklists:



DMS-CG

– DMS8000 Network, Fire & Intrusion Connectivity Guide (document

no. A6V10062425)



DMS-ICC

- Product-specific (e.g. MM8000) Installation, Configuration & Com-

missioning guide

Items needed for configuration



All FS20/FS720 Stations are equipped with the

FCA2013-A1 License key L2

(A5Q00018857) for enabling the BACnet protocol.



FS20/FS720 System commissioned. SiB-X export file available.



Danger Management software installed (at least Composer)

see

DMS-ICC



To set the IP address(es) on NK8237, NW8202 is required

p. 28



NK8237 unit(s) must be installed.



The network configuration must be defined, including all IP addresses, IP masks
and the default gateway.

If multiple routing is required, each route should be defined, including the destina-
tion IP address, mask, and gateway.

Engineering

tools

Automation level

Field level

BACnet/IP

Modbus Slave

BACnet client

BACnet server

Modbus Master

FC2020

GAP

Modbus RTU (RS-232)

ETH1

Ethernet

Modbus GW

Modbus device

Sinteso Works

Composer

SiB-X

CSV

3rd party configuration tool

Engineering data export

Configuration download

Содержание NK8237 MP4.40





































































Результаты поиска

Содержание NK8237 MP4.40

Отзывы:

Siemens NK8237 MP4.40, Установка, Функции и Настройка, Пусконаладка, Страница: 30 / 68

Результаты поиска

Содержание NK8237 MP4.40

Отзывы: