Siemens MD-12HD Скачать руководство пользователя страница 62

Страница: 62 / 74

Siemens Industry, Inc.

b) ViewPoint HD.

If an internet utility is not available, ViewPoint HD has a built-in conversion utility under the

Advanced Tab.

Enter

100.00

and press the

Convert to Modbus Integers

button.

This utility identifies that the MSW and LSW registers need to be set to

17096

(decimal)

respectively. If hexadecimal notation is required these decimal values can be converted using a
utility such as the MS Windows Calculator (under Programmer mode) as shown below.

After padding, we also arrive at

0x42C8 0x0000

as the MSW and LSW register values respectively.

Step 2.

Identify which configuration registers control the CH1 CT Full Scale Rating

a. Refer to the MS Excel Register List (USB drive or at

www.DENTinstruments.com

)

b. Use ViewPoint HD to discover the address of displayed data.

a) Open the MS Excel Register List and locate the CH1 CT Full Scale Rating Registers under USER

CONFIG POINTS group.

Содержание MD-12HD











































































Результаты поиска

Содержание MD-12HD

Отзывы:

Siemens MD-12HD, Руководство пользователя, Страница: 62 / 74

Результаты поиска

Содержание MD-12HD

Отзывы: