Siemens MD-12HD Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 74

Siemens MD-12HD Скачать руководство пользователя страница 17

Siemens Industry, Inc.

16

Meter Configuration - Details

This section is written to support setting up the MD-xxHD

in an office environment

and

configuring the power meter for a pre-determined configuration. In many cases, the
setup is standardized for an organization or project. In other cases, the setup can be
documented and emailed to an installer. The setup can also be performed on-site and
reflect “as-built” configurations.

The MD-xxHD meter cannot be configured using ViewPoint HD over a serial port. RS-485 serial
network configurations must be pre-configured or use Modbus/BACnet hosts.

This section describes the use of the ViewPoint HD Windows Application. If this interface
cannot be used, see the section on using the simplified MD-xxHD Web App interface. The web
browser can be accessed from the USB port to support Mac users.

Install the ViewPoint HD Software

Insert the ViewPoint HD thumb drive into the computer or download from:

https://www.dentinstruments.com/siemens

Locate the ViewPoint HD Installer and open this folder.

Typical Installation

Double-click the

“

RunMe to Install ViewPoint HD.bat

”

batch file to install ViewPoint and its support files

in Windows default location. This option works for most users.

«
...
15
16
17
18
19
...
»

Содержание MD-12HD











































































Отзывы:

Нет отзывов