Siemens MD-12HD Скачать руководство пользователя страница 16

Страница: 16 / 74

Siemens Industry, Inc.

Verification and Communication Overview

▪

Can be modified with power applied to the meter.

Tools

Typical Work

•

Tablet, Smart Device (Web Page

Based), or
Laptop computer (ViewPoint HD
Software)

•

On site troubleshooting

•

Multi Meter, Current Clamp

•

Camera

•

Locate the power meter

•

Confirm RTU device

•

Add wire terminations (if required)

•

Confirm meter communication

settings

•

Meter health metrics (check for setup

errors)

•

Analytics (ViewPoint HD)

•

Correct instrumentation

•

Set alarms

•

Set security PINs

•

Checklist

RTU Programming and Scripting Overview

Tools

Typical Work

•

Laptop PC (Remote Access to RTU)

•

Remote troubleshooting

•

Confirm meter communication

settings

•

Confirm communication protocols

•

Exercise remote connectivity

•

Run configuration scripting

•

Set alarms

•

Set security PINs

•

Confirm data integrity

Содержание MD-12HD











































































Результаты поиска

Содержание MD-12HD

Отзывы:

Siemens MD-12HD, Руководство пользователя, Страница: 16 / 74

Результаты поиска

Содержание MD-12HD

Отзывы: