Siemens MD-12HD Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 74

Siemens MD-12HD Скачать руководство пользователя страница 33

Siemens Industry, inc.

32

MacOS Users

ViewPoint HD is a Windows application and does not run on MAC OS. MAC users can, however, make
use of the MD-xxHD Web App interface through the USB port by installing a CDC-EEM driver. This driver
is available in the Media Distribution materials or can be downloaded from the DENT Instruments web
site.

1.  Users must have OS version of 10.11.1 or higher.
2.  Drag the file dentinstruments-2.03a1.dmg onto the desktop.
3.  Double-click the dmg file to initiate the MAC installer.
4.  Follow the installation prompts.
5.  Reboot the MAC after the installation process is complete.
6.  Connect the MD-xxHD meter to the MAC with USB cable.
7.  Open Safari browser and type IP address 169.254.1.5 to access the MD-xxHD Web App
8.  If no login credentials are setup, click on

LOGIN

button with blank for password.

9. The MD-xxHD Web App checks for login credentials and, if passed, opens Real Time Web Page.

«
...
31
32
33
34
35
...
»

Содержание MD-12HD











































































Отзывы:

Нет отзывов