Siemens MAMMOMAT Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

Siemens MAMMOMAT Скачать руководство пользователя страница 11

4 Compression System

MAMMOMAT Balance

SPB7-115.831.01 Page 11 of 22

Siemens AG

Maintenance Instructions

Rev.01 05.04

Medical Solutions

4 Compression System

SIM

Testing the manual movement

•

System OFF

•

Move compression plate attachment Up/Down it must move free and without friction and noise

SIM

Testing compression plate support

•

Check that levers and retain pins are not damaged and release normally.

•

Check for fixation of each compression plate

SIM

Testing lexan of compression plates for wear and tear

•

Check each plate for possible damage that can result harmful to patients.

SIM

Check foot pedal switches functionality

•

Check for each pedal switch functionality

SIM

Testing magnification support fixation

•

Check that the magnification plateform can be fixed at 1,5x and 2x

SIM

Testing the “Compression” force

•

Use shifted compression plate, position a bathroom balance on the top of the table and tennis ball,
select maximum compression force and check it.

SIM

Testing the “Decompression” force

•

Move compression plate up and check that force to stop it by hand is very light.

PMF Compression Thickness Display

•

With large focus selected and compression plate in place check for compression thickness
indication using Plexiglas phantom blocks to simulate breast thickness.

•

Repeat with small focus and magnification pla compression plate

If thickness value is not correct refer to service instructions SPB7-115.840.01…, chapter of dosimeter
where source to skin distance calibration is described.
Breast thickness is obtained by such value subtracted by F.F.D.

«
...
9
10
11
12
13
...
»

Содержание MAMMOMAT























Отзывы:

Нет отзывов