Siemens HB74AA 0 Series, Инструкция по эксплуатации

Страница: 10 / 24

10
ã=
Significant health risks!
Do not place non-stick baking tins or trays in the oven during
self-cleaning. The intense heat removes the non-stick surface
and creates toxic gases.
Setting
Once the cleaning level has been selected, set the oven.
1.
Select the Self-cleaning
x
function with the function control
knob.
2.
Set the required cleaning level using the
@
or
A
sensors.
The display panel will show the cleaning level and the
x
symbol. Self-cleaning starts within a few seconds.
The oven door locks shortly after the function has started. The
H
symbol lights up on the display panel. Only when the
H
symbol turns off can the oven door be opened again.
Self-cleaning has ended.
The display panel will show ‹‹ : ‹‹ . The oven will stop heating.
Turn the function control knob to the zero setting. The oven
switches off. The oven door can be opened again when the
H symbol on the display panel turns off.
Changing the cleaning level
The cleaning level cannot be changed once it has started.
Stopping the self-cleaning
Turn the function control knob to the zero setting. The oven
switches off. The oven door can be opened again when the
H symbol on the display panel turns off.
Delaying the end time
The oven allows you to programme the self-cleaning end time.
Self-cleaning can therefore be programmed at night for
example, leaving the oven free for use during the day.
Programme as described in section 1 and 2. Before starting the
self-cleaning, press the
0
sensor three times and delay the
end time with the
@
or
A
sensors.
The oven is set to standby. The display panel will show the
cleaning level and the
y
symbol. When self-cleaning starts, the
cleaning level and the
x
symbol are shown. The
y
symbol
switches off.
Viewing the time settings
To view the duration of the cleaning level or the end time of the
self-cleaning press the 0 sensor repeatedly until the required
symbol lights up. The corresponding value will be shown for a
few seconds on the display panel.
After using the self-clean function
Once the inside of the oven has cooled, clean the ash remains
using a damp cloth.
Care and cleaning
If cleaned and properly cared for, your oven will keep its bright
appearance and operating performance for many years to
come. Advice on how to care for and clean your oven is
provided below.
Notes
■
Different colours may be seen in your front panel due to the
various materials used in its manufacture, such as glass,
plastic and metal.
■
Dark patches in the door's glass panel may seem to be dirt
but they are in fact reflections from the oven light.
■
Enamel burns at very high temperatures. This may cause
slight discolouration. This is normal and does not affect the
oven's operation. The edges of thin baking trays may not be
completely enamelled. They may therefore feel slightly rough,
although their corrosive protection will be unaffected.
Cleaning products
Follow the information provided in the table to avoid damaging
the various oven surfaces by using unsuitable cleaning
products. Do not use
■
abrasive or acidic cleaning products,
■
strong products containing alcohol,
■
scourers or hard sponges,
■
high-pressure or steam cleaners.
Wash new cloths thoroughly before use.
Zone Cleaning products
Front panel Hot water and a little soap:
Clean with a dishcloth and dry with a
soft cloth. Do not use window
cleaner or a glass scraper.
Stainless steel Hot water and a little soap:
Clean with a dishcloth and dry with a
soft cloth. Immediately remove any
water marks, grease, cornflower or
egg white stains since corrosion
could occur underneath these marks
or stains.
Special products for the care of
stainless steel and which are
suitable for hot surfaces may be
obtained from Technical Assistance
Service centres and specialist retail
outlets. Use a very fine soft cloth to
apply the cleaning product.
Glass panel Glass cleaning products:
Clean using a soft cloth. Do not use
a glass scraper.
Display Glass cleaning products:
Clean using a soft cloth. Do not use
alcohol, vinegar or other abrasive or
acidic cleaning products.
Glass panel Glass cleaning products:
Clean using a soft cloth. Do not use
a glass scraper.
Door covering Only use products specially for
cleaning stainless steel (these can
be obtained from the Technical
Assistance Service or from specialist
shops). Follow the manufacturer's
instructions.