Siemens DF8000 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 46

Siemens DF8000 Скачать руководство пользователя страница 37

33

Building Technologies

048_DMS_DF8000_ICC_MP4.15_A6V10081388_c_en.doc

Fire Safety & Security Products

06.2008

Action:

replace the module.

The whole unit doesn't turn on

1.

Power supply voltage absent or too low.

Action:

verify power supply voltage.

2.

Voltage polarity is inverted.

Action:

verify the polarity and exchange the poles as necessary.

The Inputs/Output signals do not operate properly

1.

The I/O LED is permanently OFF.

Action:

remember that LEDs can be switched off with a switch setting on the

DF8003 CPU. If the problem concerns one I/O module only and it does depend
on the switch setting, then the specific module may be faulty. If the trouble con-
cerns all modules of one unit, then the DF8003 CPU could be faulty. Try to re-
place the modules.

2.

A group of I/O signal does not work, CPU Fault yellow LED flashing during start-
up when the DF8003 is powered up, this LED reports for 6 times the status of
the 6 possible I/O modules: two quick flashes indicates no response from the
module, whereas one long flash means that the module is regularly responding.

Action:

replace the module.

«
...
35
36
37
38
39
...
»

Содержание DF8000















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды