Siemens CEREBRUS PYROTRONICS AD-3XRI Скачать руководство пользователя страница 9

Страница: 9 / 12

b. Wire normally de-energized devices (extinguishing smoke removal fan,

etc.) to the NO contacts between terminals 10 and 11 in order to acti-

vate these devices on alarm.

NOTE:

Relay contacts may not be in supervisory condition when

shipped.

INSTALLATION OF SMOKE DETECTORS

CAUTION:

Air Duct Detector Models AD-3XRI/3XRILP are designed

only for those detectors shown in the Smoke Detector

Compatibility section (See Tables 1and 2). Do not use any

other detector (See Figure 3,items 14, 15 and 21).

Programming

DI-BX, DI-BX3H Detectors

Model AD-3XRI, using X Series smoke detectors, can be programmed to

respond at a specific and unique address (See Figure 8). Program each

detector by referring to the table and notes in Figure 8. Record each

device number and zone in the space provided on the detector cover.

ID-60IB, ID-60IBH, ILI-1B, ILI-1BH, ILP-1 Detectors

Model AD-3XRI/3XRILP, using ID-60IB, ID-60IBH, ILI-1B, ILI-1BH, or ILP-1

detectors, can be programmed to respond at a specific and unique system

10 11

SEE NOTE 3

Model AD-3I or AD-3ILP

Model AD-3XRI or AD-3XRILP

NOT

USED

TERMINAL

BLOCK

RED

BLACK

WIRE NUT

REQUIRED

NOT USED

RELAY

BOARD

ALARM CONTACTS

125 VAC/24 VDC, 3A

SEE NOTES 1 AND 2

ALARM CONTACTS

125 VAC/24 VDC, 3A

SEE NOTES 1 AND 2

TO NEXT

ADDRESSABLE

DEVICE

OPTIONAL

REMOTE ALARM

INDICATOR

MODEL RLX-1

OR RLX-2

ZONE WIRES FROM SIEMENS

BUILDING TECHNOLOGIES, INC.

SYSTEM XL3 CONTROL PANEL

+ +

+ _

NOTES:

1. The relay contacts are shown just after a reset pulse, which

represents the non-alarm condition.

2. If the relay contacts are being used to control 120 VAC operated

equipment, ensure that the conduit is properly attached to the internal

ground strap, using the proper conduit locking nuts.

Failure to

provide proper grounding may result in fatal electrical shock and

causes non-conformance with national and local codes.

3. Use DI-BX3, DI-BX3H, ID-60IB, ID-60IBH, ILI-1B, ILI-1BH, and ILP-1

detectors only.

Figure 6

Typical Connections for Models AD-3XRI and AD-3XRILP when used with XL3

Содержание CEREBRUS PYROTRONICS AD-3XRI













Результаты поиска

Содержание CEREBRUS PYROTRONICS AD-3XRI

Отзывы:

Бренды по названию

Популярные бренды

Siemens CEREBRUS PYROTRONICS AD-3XRI, Инструкции по установке/подключению

Результаты поиска

Содержание CEREBRUS PYROTRONICS AD-3XRI

Отзывы:

Бренды по названию

Популярные бренды