manualshive.com logo in svg

Siemens CEREBRUS PYROTRONICS AD-3XRI, Инструкции по установке/подключению

Поделиться
Скачать
Siemens CEREBRUS PYROTRONICS AD-3XRI Скачать руководство пользователя страница 3

3

OPERATION

When the AD-3XRI/3XRILP (AD-3XRI 

or

 AD-3XRILP) is operating, a

sample of air is drawn from the duct and passed through the sampling

chamber at low velocity by means of the inlet sampling tube. The air

sample passes through the smoke detector mounted in the duct housing

and is exhausted back into the duct through the outlet sampling tube.

Alarm Indication

The  XL3, IXL, and MXL Control Panels have LEDs for alarm indication

that are used with the AD-3XRI/3XRILP.  Refer to Table 3 above.
The LED on the detector in alarm can also be turned on or off by system

command.

Alarm Condition

When used with the XL3, IXL, or MXL Control Panel, the Model AD-3XRI/

3XRILP operates directly from the control panel. An alarm condition on

either of these systems is indicated by visual and audible system devices.

On XL3 Systems the alarm is also indicated on the DAX module and any

optional printers used. On MXL Control Panels the alarm is indicated on

the MKB-1/-2 and on any optional printers used.
After a fire is extinguished, and all products of combustion are cleared

from the duct system, each system can be reset at its respective control

panel, and the XL3 also can be reset at its optional printer, if available.

Trouble Condition

A trouble condition from an AD-3XRI/3XRILP is indicated by visual and

audible system devices connected to the control panel in an XL3, IXL, or

MXL Control Panel, depending on the type of system in which it occurs.

It can also be indicated by an optional printer. Call your Authorized

Siemens Building Technologies, Inc. Service Representative when a

trouble occurs.
For further information, refer to the appropriate Operation Instructions:

System XL3 

OPERATION INSTRUCTIONS, 

P/N 315-082989

MXL/MXLV Control Panel 

OPERATION INSTRUCTIONS, 

P/N

315-092117

System IXL 

OPERATING INSTRUCTIONS, 

P/N 315-079651

MOUNTING THE AIR DUCT HOUSING
Location on Duct System

Locate the air duct detector in the main supply duct, downstream from the

filters and positioned so as to operate reliably in case of smoke in any

part of the air stream. In instances where filters are capable of removing

smoke, install detectors both upstream and downstream from the filters.

Содержание CEREBRUS PYROTRONICS AD-3XRI













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды