manualshive.com logo in svg

Siemens CEREBRUS PYROTRONICS AD-3XRI, Инструкции по установке/подключению

Поделиться
Скачать
Siemens CEREBRUS PYROTRONICS AD-3XRI Скачать руководство пользователя страница 1

Installation/Wiring  Instructions

CERBERUS PYROTRONICS

TM

Models AD-3XRI and AD-3XRILP

Air Duct Detectors

INTRODUCTION

CERBERUS PYROTRONICS

TM

 Model AD-3XRI and AD-3XRILP

Detectors are System IXL (ICON-1), System XL3, and MXL Control Panel

compatible air duct detectors with an auxiliary relay. They are designed

for use in heating, ventilating, and air conditioning duct systems. Model

AD-3XRI uses ionization smoke detectors, and Model AD-3XRILP uses

photoelectric smoke detectors to detect the presence of combustion

products in a duct system. (Refer to 

TECHNICAL DATA 

below for infor-

mation on compatible detectors.)
When smoke or combustion products are detected, shutdown of the duct

system and/or operation of supplementary equipment is provided by the

related system control panel.

TECHNICAL DATA

Smoke Detector Compatibility

TABLE 1

AD-3XRI COMPATIBILITY

     

System/Module                                     Compatible Detectors

System XL3                  DI-BX3, DI-BX3H, ID-60IB, ID-60IBH, ILI-1B, ILI-1BH

MXL Control Panel       ID-60IB, ID-60IBH, ILI-1B, ILI-1BH

System IXL (ICON-1)   ILI-1B, ILI-1BH

TABLE 2

AD-3XRILP COMPATIBILITY

   

System/Module                                        Compatible Detectors

System XL3

      ILP-1

MXL Control Panel

      ILP-1

Cerberus Division

P/N 315-093235-5

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

50 East Pearce Street

Richmond Hill, Ontario L4B 1B7 CN

Содержание CEREBRUS PYROTRONICS AD-3XRI













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды