Siemens BANY Agent Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 46

background image

BANY Agent

9

Compact Operating Instruction

WARNING

Replacing components

EXPLOSION HAZARD

SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I; DIVISION „
OR ZONE..

WARNING

Requirements for the cabinet/enclosure

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2,
the device must be installed in a cabinet or a suitable enclosure.

Notices for use in hazardous areas according to ATEX

WARNING

Requirements for the cabinet/enclosure

To comply with EU Directive 94/9 (ATEX95), this enclosure must meet the requirements of at
least IP54 in compliance with EN 60529.

WARNING

Suitable cables for temperatures in excess of 70 °C

In the cable or conduit entry point exceeds 70°C or the branching point of conductors exeeds
80°C, special precautions must be taken. If the equipment is operated in an air ambient in
excess of 50°C, only use cables with admitted maximum operating temperature of at least
80°C.

WARNING

Protection against transient voltage surges

Provisions shall be made to prevent the rated voltage from being exceeded by transient voltage
surges of more than 40%. This criterion is fulfilled, if supplies are derived from SELV (Safety
Extra-Low Voltage) only.

«
...
7
8
9
10
11
...
»

Содержание BANY Agent















































Отзывы:

Нет отзывов

Похожие инструкции для BANY Agent

Бренд: OMA Страницы: 53

Бренд: Dickey-John Страницы: 109

Бренд: TEXTILE ID Страницы: 4

Бренд: FARFISA INTERCOMS Страницы: 2

Бренд: Aiwa Страницы: 30

Бренд: Fermax Страницы: 16

Бренд: YASKAWA Страницы: 135

Бренд: J&M Страницы: 8

Бренд: fadini Страницы: 20

Бренд: Sensitron Страницы: 11

Бренд: Rain Bird Страницы: 5

Бренд: Grundig Страницы: 16

Бренд: Dahua Страницы: 36

Greengate ControlKeeper 4

Бренд: Eaton Страницы: 24

Бренд: Forge Electronics Страницы: 10

Бренд: Ravaglioli Страницы: 28

Бренд: ATL Страницы: 46

KD8023E6 Series

Бренд: HIKVISION Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды