Siemens BANY Agent Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 46

Siemens BANY Agent Скачать руководство пользователя страница 41

BANY Agent

41

Compact Operating Instruction

8 Approvals

8.1 BANY Agent approvals, certificates

Not

The specified approvals only when the corresponding mark is printed on the product. You
can check which of the following approvals have been granted for your product by the
markings on the type plate.

EC directives

SIMATIC NET products meet the requirement and aims of the following EC directives.

EMC directive (electromagnetic compatibility)

The SIMATIC NET product meets the requirement of the EC Directive:
2004/108/EG „electromagnetic compatibility“

The product is designed for use in the following areas:

Area of application

Requirements

Emission

Immunity

Industrial area

EN 61000-6-4: 2011

EN 61000-6-2: 2005

WARNING

Personal injury and damage to property occur.

The installation of expansions that are not approved for SIMATIC NET products or their target
systems may violate the requirements and regulations for safety and electromagnetic
compatibility.

Only use expansions that are approved for the system.

«
...
39
40
41
42
43
...
»

Содержание BANY Agent















































Отзывы:

Нет отзывов