Siemens BANY Agent Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 46

background image

BANY Agent

29

Compact Operating Instruction

5.4 Digital In/Outputs

The digital Inputs and Outputs are floating switches by breaking the contact.

Connecting the digital In/Outputs

The digital In/Outputs contacts are connected to a 4-pin plug-in terminal block.
The digital In/Outputs can be subjected to a maximum load of 50 mA (safety extra low
voltage SRLV 24 VDC).

Pin number

Assignment (24 VDC)

Labeling

DI/DO

In/Output 24 V DC

SGND

Ground for In/Output

SGND

In/Output 24 V DC

DIDO

Ground for In/Output

5.5 Connecting functional ground

Installation on a DIN rail

The device is grounded over the DIN rail.

S7 standard rail

The device is grounded over the rear panel and the neck of the screw.

Wall mounting

The device is grounded by the securing screw in the unpainted hole..

Please note that the BANY Agent must be grounded over one securing screw with
minimum resistance.

If an BANY Agent is mounted on a non-conducting base, a grounding cable must be
installed. The grounding cable is not supplied with the device. Connect the paint-free
surface of the BANY Agent to the nearest grounding point using the grounding cable.

«
...
27
28
29
30
31
...
»

Содержание BANY Agent















































Отзывы:

Нет отзывов

Похожие инструкции для BANY Agent

Бренд: OMA Страницы: 73

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 112

Multi-room system

Бренд: Systemline Страницы: 22

Бренд: Concertone Страницы: 12

Бренд: Barton Страницы: 36

Бренд: Cyrus Страницы: 6

Бренд: Velux Страницы: 11

Бренд: ZiLOG Страницы: 241

HERCULES 6.5 PLUS

Бренд: Fenix Страницы: 24

USB-1408FS-Plus

Бренд: Measurement Computing Страницы: 29

Бренд: urmet domus Страницы: 13

Бренд: Omron Страницы: 114

Бренд: Sonoro Страницы: 336

Бренд: Lilin Страницы: 11

Бренд: Dahua Страницы: 36

MASTERSTREAM 1000 Series

Бренд: Task Force Tips Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды