Siemens Acvatix SAS Series Скачать руководство пользователя страница 41

Страница: 41 / 61

41 / 60

Siemens

Actuators SAS.., SAT.. for valves

CE1P4041en

Smart Infrastructure

Functions

and control

2019-04-09

Min / Max (depends on Min/Max settings)

Stop

Backup
mode

513,

514, 515

In case the communication to the controller is lost, the device can be

configured to go into a defined state.

Default setting mode is “keep last setpoint”, i.e. in case of communication

loss, the device controls to the last received setpoint.

If the backup mode is enabled, it can be configured as follows:

go to a predefined backup position

keep current position

Restarting
the device

256

Restarting is possible by:

Power-reset (turning operating voltage off and on) or

by “ReInitDevice” command.

Device re-initializes and sets all process values to defaults.

Reset

The actuator supports the following re-initialization / reset behaviour:

Local reset by push-button

Remote reset: Using “RemoteFactoryReset” command.

Effect of reset:

Process values: set to ex-works default values.

Parameters:

Application and actuator parameters are set to factory defaults,

Network parameters are reset only in case of local reset, not by remote

reset (otherwise loss of communication).

Not reset are: Counters, status flags, device info, and factory data.

Self test

256

When triggered, the self test drives the actuator to the detected limits and sets

the flags in register 769 according to the result (bit 09 = 1

”failed” or bit 10 = 1

“passed”).

The self test is not passed when the limits were not reached from the lower

end (results in jam). If the Min/Max limits can be exceeded, the self test is not

evaluated as failed.

Communication

Communications protocol

Modbus RTU

RS-485, not galvanically separated

Number of nodes

Max. 32

Address range

1...247 / 255

Factory settings: 255

Transmission formats

1-8-E-1 / 1-8-O-1 / 1-8-N-1 / 1-8-N-2

Factory settings: 1-8-E-1

Baud rates (kBaud)

Auto / 9,6 / 19,2 / 38,4 / 57,6 / 76,8 / 115,2

Factory settings: Auto

Bus termination

120

electronically switchable

Factory settings: Off

Communication
properties

Содержание Acvatix SAS Series






























































Результаты поиска

Содержание Acvatix SAS Series

Отзывы:

Siemens Acvatix SAS Series, Основная документация, Страница: 41 / 61

Результаты поиска

Содержание Acvatix SAS Series

Отзывы: