background image

English  

7XV5655-0BA00 

 

 
46 / 53 

 

C53000-G1176-C174-3 

 

Standards: 

IEC 60255 (product standard) 
IEEE Std C37.90.0/.1/ 
VDE 0435 
For more standards, see each function 

 

 

Insulation tests 
 

Standards: 

 
 
IEC 60255-5 and IEC 60870-2-1 

Voltage test

 (100% test) all circuits except 

auxiliary voltage and communication 
interfaces

 

2.5 kV (rms), 50 Hz 

Voltage test

 (100% test) on auxiliary voltage

 

3.5 KV DC 

Voltage test

 (100% test) only locked 

communication interfaces

 

500 V (rms), 50 Hz 

Surge withstand capability test

 (type 

test) all circuits except communication 
interfaces, class III 

 

5 kV (peak value); 1.2 / 50 µs; 0.5 J; 
3pos./neg. surges at 5s intervals 
 

 

 

 

 

 

Warning 
 

The 7XV5655-0BA00 is specifically intended for installation in a switchgear cubicle 
or distribution box. After installation, the entire area  
around the terminals must be covered. Only then is the device sufficiently protected 
against impermissible contact with live parts. 

 

 

 

 

EMC tests for immunity

 (type tests)

 

 

 

Standards: 

 

IEC 60255-6 and -22 (product standards) 
EN61000-6-2 (generic standard) 
VDE 0435 part 301DIN VDE 0435-110 

High Frequency Test 

IEC 60255-22-1, Class III 
and VDE 0435 Part 303, Class III

 

2.5 KV (peak); 1 MHz;

ז

 = 15 ms; 400 surges per s; 

test duration 2s; Ri = 200 

 

 

Electrostatic Discharge 

IEC 60255-22-2, Class III 

8 KV contact discharge; 15 KV air discharge 
pos./neg. polarity, 150 pF; Ri = 330 Ù 

Irradiation with RF field

, frequency sweep

 

IEC60255-22-3, Class III 
IEC61000-4-3, Class III 

10 V/m, 80 MHz to 1000 MHz: 80% AM, 1 kHz 

Irradiation with RF field

, single frequencies

 

IEC60255-22-3, IEC61000-4-3 

-  

amplitude-modulated 

 
- pulse-modulated

 

Class III:  10 V/m 
 
80, 160, 450, 900 MHz; 80 % AM 1kHz;  
duty cycle > 10 s 
900 MHz; 50% PM, repetition frequency 200 Hz 

Fast transients / bursts  

IEC 60255-22-4 and IEC61000-4-4 
Class IV 

4 kV; 5/50 ns; 5 kHz; burst length = 15 ms; 
Repeat rate 300 ms; pos./neg. polarity; 
test duration 1 min.; Ri = 50 Ù 

High energy surge voltages (SURGE) 

EN61000-4-5 insulation class 3 
- Auxiliary voltages 
 
 

Pulse: 1.2/50 µs 
 
common mode; 2 KV; 12 

; 9 µF 

differential mode : 1 kV; 2 

; 18 µF 

 

Содержание 7XV5655-0BA00






















































Отзывы: