Siemens 7ME652 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 86

Siemens 7ME652 Скачать руководство пользователя страница 15

2.4

Installation in hazardous area

WARNING

Equipment used in hazardous locations
Equipment used in hazardous locations must be Ex-approved for the region of installation and

marked accordingly. It is required that the special conditions for safe use provided in the

manual and in the Ex certificate are followed!

Hazardous area approvals

The device is approved for use in hazardous area and has the following approvals:
● MAG 5100 W DN 15 to 1200: FM / CSA Class I, Div. 2

WARNING

Suitable hazardous area approval
Make sure the hazardous area approval is suitable for the environment in which the device

will be installed.

WARNING

All approvals are based on non-flammable processes only!

WARNING

Potential equalization
In operation, the output is earthed through the conductive medium being measured and

therefore potential equalisation is necessary throughout the hazardous area.
The apparatus housing shall be connected to the potential equalising conductor in the

hazardous area.

WARNING

Laying of cables
Cables for use in hazardous area must satisfy the requirements for having a proof voltage

< AC 500 V applied between the conductor/ground, conductor/shield and shield/ground.
Connect the devices that are operated in hazardous areas as per the stipulations

applicable in the country of operation.

Safety notes

2.4 Installation in hazardous area

SITRANS FM MAG 5100 W

Operating Instructions, 01/2020, A5E03063678-AC

15

«
...
13
14
15
16
17
...
»

Содержание 7ME652























































































Отзывы:

Нет отзывов